Search results
From Diustou Wiki
Page title matches
File:PWM control backlight manual.pdf (0 × 0 (561 KB)) - 14:46, 22 March 2021File:Fan-4020-PWM-5V-3.jpg (1,440 × 1,080 (222 KB)) - 11:13, 22 March 2021- ...es=[[File:Fan-4020-PWM-5V-3.jpg|300px|link=https://{{SERVERNAME}}/fan-4020-pwm-5v.htm]] |interfaces={{Category|PWM}}1 KB (231 words) - 18:06, 23 March 2021
Page text matches
- * [[Fan-4020-PWM-5V]]9 KB (1,169 words) - 17:40, 20 February 2025
- *Supported Interfaces: UART/GPIO/ADC/PWM/SPI/I2S/I2C **2 PWM outputs6 KB (861 words) - 14:33, 13 January 2025
- ...{{Category|SPI}}{{Category|UART}}{{Category|I2C}}{{Category|AD}}{{Category|PWM}}816 bytes (104 words) - 18:08, 23 March 2021
- ...es=[[File:Fan-4020-PWM-5V-3.jpg|300px|link=https://{{SERVERNAME}}/fan-4020-pwm-5v.htm]] |interfaces={{Category|PWM}}1 KB (231 words) - 18:06, 23 March 2021
- ===PWM: Buzzer testing===11 KB (1,816 words) - 09:25, 23 March 2021
- **Input: PWM44 KB (6,541 words) - 16:28, 22 January 2025
- **Input: PWM **Input: PWM44 KB (6,272 words) - 18:19, 12 February 2025
- **Input: PWM **Input: PWM43 KB (6,163 words) - 17:03, 7 February 2025
- ...the resistor and wire the top pad to P1 of Raspberry Pi and control it by PWM. gpio -g pwm 18 02 KB (305 words) - 09:25, 23 March 2021
- *[[:File:PWM control backlight manual.pdf|PWM control brightness of LCD]] {{FAQ|Can 7inch HDMI LCD (H) use an external PWM signal to control the backlight?12 KB (1,969 words) - 09:25, 23 March 2021
- *2 × SPI, 2 × I2C, 2 × UART, 3 × 12-bit ADC, 16 × controllable PWM channels1 KB (184 words) - 15:22, 19 March 2021
- ...t enable pins, active high enable. When they are driven to High level, the PWM pulse will be outputted from M1, M2, M3 and M4, so as to control the speed8 KB (1,285 words) - 16:14, 22 March 2021
- This sensor has both digital PWM and SMBus (System Management Bus) output. In this document, we only introdu8 KB (1,239 words) - 18:00, 22 March 2021
- *Command explanation: '''gpiozero.LED(pin, pwm, active_high, initial_value)'''3 KB (439 words) - 14:02, 11 February 2025
- *Command description: '''LEDBoard(pin, pwm, active_high, initial_value)''' *** pwm:9 KB (1,380 words) - 14:00, 11 February 2025
- *Command description: '''gpiozero.LED(pin, pwm, active_high, initial_value)'''5 KB (783 words) - 15:56, 12 February 2025
- ...specify None (unlike the parent class) because there is no way to tell the PWM not to change the state of the pin.3 KB (483 words) - 17:57, 12 February 2025
- *Command description: '''gpiozero.OutputDevice(pin, pwm, active_high, initial_value)'''3 KB (381 words) - 17:57, 12 February 2025
- *Command description: '''LEDBoard(pin, pwm, active_high, initial_value)''' ***pwm:3 KB (452 words) - 17:57, 12 February 2025
- ** pwm:3 KB (442 words) - 13:56, 11 February 2025