Search results
From Diustou Wiki
Page title matches
- ***pull_up: Internal pull-up/pull-down resistor setting,5 KB (728 words) - 15:24, 12 February 2025
Page text matches
- ...ning-proof and surge-suppress, 15KV ESD protection (onboard 120R balancing resistor)3 KB (423 words) - 18:03, 23 March 2021
- ...ult, it is the TNOW pin. To change it to a DTR pin, short-circuit the 4.7K resistor by removing it and then soldering the pads together.3 KB (432 words) - 14:57, 14 January 2025
- * The board includes reserved 120R termination resistor pads to enhance signal transmission stability and reduce interference. * Onboard 120R termination resistor selection DIP switch to enhance signal transmission stability.8 KB (1,159 words) - 17:05, 5 February 2025
- * The board includes reserved 120R termination resistor pads to enhance signal transmission stability and reduce interference.4 KB (486 words) - 17:08, 5 February 2025
- * The board has reserved 120R termination resistor pads to enhance signal transmission stability and reduce interference. * The board features a 120R termination resistor DIP switch to enhance signal transmission stability.8 KB (1,168 words) - 17:05, 5 February 2025
- * The board includes 120R terminal resistor pads to enhance signal transmission stability and reduce interference.6 KB (813 words) - 17:07, 5 February 2025
- {{Category|Resistor}}1 KB (195 words) - 17:08, 23 January 2025
- * The board has reserved 120R terminal resistor pads to improve signal transmission stability and reduce interference. * On-board 120R terminal resistor DIP switch for improving signal transmission stability.6 KB (951 words) - 17:05, 5 February 2025
- * The board has reserved 120R termination resistor pads to enhance signal transmission stability and reduce interference.4 KB (651 words) - 17:07, 5 February 2025
- * The board includes 120R termination resistor pads to enhance signal transmission stability and reduce interference. * The board includes 120R termination resistor pads to enhance signal transmission stability and reduce interference.10 KB (1,358 words) - 17:04, 5 February 2025
- * The board includes 120R terminal resistor pads, enhancing signal transmission stability and reducing interference.7 KB (951 words) - 17:07, 5 February 2025
- **Current Limiting Resistor: Included ...he Arduino development board, configure the OUT pin as input with a pullup resistor, and leave the GND pin floating.44 KB (6,541 words) - 16:28, 22 January 2025
- === Color-coded Resistor === ...body only has a single black band in the middle, it represents a zero-ohm resistor.23 KB (3,653 words) - 16:28, 22 January 2025
- **Current Limiting Resistor: 330Ω **Current Limiting Resistor: 330Ω44 KB (6,272 words) - 18:19, 12 February 2025
- **Current Limiting Resistor: 330Ω **Current Limiting Resistor: 330Ω43 KB (6,163 words) - 17:03, 7 February 2025
- You need to remove the resistor and wire the top pad to P1 of Raspberry Pi and control it by PWM.2 KB (305 words) - 09:25, 23 March 2021
- 7 KB (1,031 words) - 09:25, 23 March 2021
- * The board has reserved 120R termination resistor pads to increase signal transmission stability and reduce interference. * Onboard 120R termination resistor DIP switch to enhance signal transmission stability.6 KB (884 words) - 17:04, 5 February 2025
- * The board has reserved 120R termination resistor pads to enhance signal transmission stability and reduce interference.4 KB (645 words) - 17:06, 5 February 2025
- * The board has reserved 120R termination resistor pads to enhance signal transmission stability and reduce interference. * The board has reserved 120R termination resistor pads to enhance signal transmission stability and reduce interference.9 KB (1,306 words) - 17:04, 5 February 2025
